| Accessories for the Cowells
Vertical Milling Machine
|
| RGB14 |
Drill Chuck |
A high precision 0 - 4mm (5/32") drill chuck supplied with mounting
arbor. |
£108.00
|
|
| RGB15 |
Drill Chuck |
A 0 - 6.3mm (1/4") drill chuck supplied with mounting arbor. |
£61.50
|
|
| RGB16 |
Drill Chuck |
A 0 - 9.5mm (3/8") drill chuck supplied with mounting arbor. |
£79.50
|
|
| B23 |
Imperial Collet Set |
Imperial Collets for the (B100) Vertical Milling Machine are
sized: 1/8", 3/16", 1/4", 3/8". |
£156.50
|
|
| B24 |
Metric Collet Set |
Metric Collets for the (B100) Vertical Milling Machines are sized: 3mm,
4mm, 5mm, 6mm, 7mm, 8mm, 9mm, l0mm. |
£310.00
|
| B25 |
Individual Collets |
Any imperial or metric size of Collet may be purchased. |
£41.00
|
| B26 |
Blank Collet |
A Blank Collet is available and can be bored and slit to a special size
requirement by the Vertical Milling Machine owner or by Cowells, (please
contact us for details). |
£25.00
|
|
| RGB56 |
Angle Plate |
The angle plate is of cast iron and is here depicted bolted to the lathe's
faceplate (RG28) thus ensuring that the surface about to be machined ("faced")
will be square to the surface mounted on the angle plate. |
£40.45
|
|
| RGB57 |
Machine Vice |
The vice body is of cast iron, machined to close tolerances and has four
fixing holes. The screw has a hexagonal head to aid clamping. The steel
jaw may be locked into position via a cap head screw and square nut running
in its own channel in the vice body. Tee-nut fixings are supplied. |
£92.40
|
|
| RGB61 |
Dividing Head
(includes one division plate RGB62) |
The solid steel body of the dividing head is ground on all faces and is
drilled to accept studs up to 6mm diameter. It is capable of being mounted
on two of its faces. The spindle has the same 14mm x 1mm thread as the lathe
chucks and is hollow with a no.0 Morse taper. The spindle is driven by a
40:1 ratio worm and wheel; adjustable to eliminate any backlash. A spindle
clamp is also provided. A steel raising block is also supplied should clearance
for the mounting of a 3 Jaw Chuck (RG9) on the Vertical Milling Machine
(B100) be required, for example. The unit is supplied with fixing studs
and the appropriate tee-nuts. |
£640.00
|
|
| RGB62 |
Division Plate |
These are of steel and are ground. Seven plates are available (including
a blank).
| Plate A - 15-21-37 |
| Plate B - 16-23-39 |
| Plate C - 17-27-41 |
| Plate D - 18-29-43 |
| Plate E - 19-31-47 |
| Plate F - 20-33-49 |
|
£55.00
each
|
|
| RGB63 |
Blank Division Plate |
This may be machined by Cowells or the customer to special requirements.
The above plates cover all numbers up to 40 and the following up to 120:-
41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 52, 54, 55, 56, 57, 58, 60, 62,
64, 65, 66, 68, 70, 72, 74, 75, 76, 78, 80, 82, 84, 85, 86, 88, 90, 92,
94, 95, 98, 100, 104, 105, 108, 110, 115, 116, and 120, and on to a maximum
of 392 divisions. |
£30.00
|
|
| RGB66 |
Tee Nut Set |
A set of six work securing Tee-nuts. Use them for all tee slots, face
plates etc |
£17.50
|
|
| B67 |
Clamping Kit |
A set of tee-nuts, studs and clamps for securing work to the Vertical
Milling Machine table. |
£70.00
|
|
| B68 |
15mm - 30mm Flycutter |
Bored to accept 3/16" dia. tooling. Two locking grub
screws are provided. |
£47.50
|
|
| B69 |
30mm - 60mm Flycutter |
The 30mm - 60mm flycutter is bored to accept 5/16" dia. tooling.
Two locking grub screws are provided. |
£57.00
|
|
| RGB70 |
Chuck & Drill Chuck Arbors |
No 6 - Vertical Mill/ suits (RGB14) 'OJ' |
£36.00
|
|
| No 7 - Vertical Mill/ 3/8 x 24/suits (RGB15) |
£29.00
|
| No 8 - Vertical Mill/14mm x 1.5mm |
£51.00
|
| RGB72 |
Blank Arbor (No 4) |
V.Mill M/C 16.5mm dia x 40mm length |
£25.00
|
|
>
| BG74 |
Motor |
A 240/220 volt D.C. 125 watt output, continuously rated, 4000 r.p.m. motor.
May be used in conjunction with the BG74a (detailed below) |
P.O.A.
|
|
| BG74A |
Control Board |
An electric motor speed control board to be used with (BG74) D.C. Motor.
Supplied with a potentiometer and wiring diagram (AC input.) |
P.O.A.
|
|
| RGB82 |
Drive Belt |
V.Mill drive belt for (B100) Vertical Milling Machine. |
P.O.A.
|
|
