| Zubehör für
Cowells 90CW Uhrenmacherdrehbank |
| RG9 |
3-Backenfutter |
A 3-jaw, 60 mm dia. universal chuck threaded
M14 x 1mm pitch. The (G200) 90 CW Lathe requires a '90 CW
adaptor' (G13) to enable the mounting of 3- and 4- jaw
chucks. |
£395.00
|
|
| RG10 |
4-Backenfutter |
4-jaw, 60 mm diameter chuck threaded M14 x 1mm
pitch. The 4-jaw chuck is predominantly used for holding
irregular shapes. The (G200) 90 CW Lathe requires a '90 CW
adaptor' (G13) to enable the mounting of 3- and 4-jaw
chucks. |
£240.00
|
|
| G13 |
3- und 4-Backenfutter adapter |
3- and 4-jaw chuck mounting arbor for the
(G200) 90CW lathe. This arbor fixes to the 90 CW lathe
headstock spindle via 3 xM4 cap head bolts and provides a
M14 x 1mm thread for mounting (RG9) 3-jaw chuck, (RG10)
4-jaw chuck and (RG52) slitting saw arbor. The arbor is
through bored 8mm diameter to allow bar material to pass
through chuck and headstock spindle. |
£59.00
|
|
| RGB14 |
Bohrfutter und Dorn |
Hoher Präzision 0 - 4mm Bohrfutter und Dorn |
£108.00
|
|
| RGB15 |
0 - 6.3mm Bohrfutter und Dorn |
£61.50
|
|
| RGB16 |
0 - 9.5mm Bohrfutter und Dorn |
£79.50
|
|
| G19 |
UM Spannzangen 8mm |
0,3mm und 0,4mm Spannzangen (je) |
£184.00
|
|
| G20 |
0,5mm bis 0,9mm Spannzangen in 0,1mm-Schritten
(je) |
£175.00
|
| G21A |
1,0mm bis 1,4mm Spannzangen in 0,1mm-Schritten
(je) |
£112.00
|
| G21B |
1,5mm bis 2,9mm Spannzangen in 0,1mm-Schritten
(je) |
£98.00
|
| G22A |
3,0mm bis 8,0mm Spannzangen in 0,5mm-Schritten
(je) |
£98.00
|
| G22IMP |
1/16", 1/8", 3/16", 1/4" Englischer
Spannzangen (je). |
£105.00
|
| G22SP |
Special sizes in the range 3mm to 8mm are
available upon request |
£184.00
|
| RG28 |
Planscheibe |
A cast iron slotted work holding plate of 90mm
diameter. The (G200) 90 CW Lathe requires a '90CW Adaptor'
(G13) to enable the mounting of the faceplate. |
£69.50
|
|
| G33 |
Männliches Zentrum |
8mm shank solid centre for the tailstock.
Hardened and ground. |
£44.00
|
|
| G34 |
Weibliches Zentrum |
8mm shank solid cup centre for the tailstock.
Hardened and ground |
£44.00
|
|
| G36 |
Drehzentrum |
Running in two high quality permanently
lubricated bearings and ground for concentricity. The
shank is supplied in parallel form and requires a 6mm
horological Collet (G22). |
£85.00
|
|
| RG37A |
Bohrunterlage - normal |
Plain tailstock drill pad with
threaded shank to suit 90CW
|
£44.00
|
|
| RG38A |
Bohrunterlage - keilförmig |
Plain tailstock drill pad with threaded shank
to suit 90CW |
£53.00
|
|
| RG39 |
Fixer Setzstock |
The fixed steady has a machined tenon that
locates in the lathe bed central tee slot and is then
secured via its tee nut and bolt. The three adjustable arms
are of brass. A fixed steady ensures the rigidity and
concentricity of a long workpiece whilst machining. |
£92.00
|
|
| RG40 |
Beweglicher Setzstock |
The travelling steady affixes to the lathe's
saddle and has two adjustable brass arms. The travelling
steady is used when turning long thin bars. The steady's
brass arms resist the deflecting thrust of the lathe tool
thus ensuring a parallel finish. |
£64.40
|
|
| RG41 |
Rückwärtige Werkzeugsäule |
The rear toolpost is of steel and affixes to
the lathe's crosslide. Heavy machining operations,
particularly 'parting-off', are performed with the lathe
tool upside down in the rear toolpost. Thrust is then
transmitted into the base of the headstock considerably
reducing vibration |
£44.00
|
|
| RG42 |
Vierweg-Werkzeugsäule |
May be set up with four primary tools saving
subsequent time spent mounting tools individually |
£48.00
|
|
| RG43 |
Schnellwechselwerkzeugsäule |
The quick change toolpost is of
steel and is supplied with two toolholders, one plain for
square shanked tools and one vee grooved for round section
tools (e.g. a boring bar). (The unit can be supplied with
two plain holders if desired). Extra toolholders (RG44) may
be obtained individually. Each toolholder is fitted with a
knurled adjusting knob for fine adjustment. The toolpost
body is sprung, into which the dovetailed toolholders clamp
via the cap head locking screw. This accessory saves
inordinate time and effort in shimming and reshimming tools
for centre height. Toolholders will accommodate 7mm maximum
tooling (fitted as standard with one plain toolholder to
(G200) 90 C.W. Lathe). |
£149.00
|
|
| RG44A |
Zusatzhalter für RG43 |
£36.00
|
| RG44B |
Zusatzhalter für RG43 |
£38.00
|
| RG46 |
13/16" Dieholder |
Two steel dieholders are available
featuring a heavy knurl and tommy bar holes to facilitate
threading. The dieholders are bored to fit over the
tailstock barrel without sideplay. The advantage of cutting
threads on the lathe is that the die is always applied
concentrically and on the true axis of the work to be
threaded, thus preventing a 'drunken' thread. Inserts can be
supplied, for other sizes please contact Cowells. |
£42.90
|
|
| RG47 |
1" Dieholder |
£47.40
|
|
| RG49 |
1-6 HSS Werkzeugsatz
especially ground for Cowells. |
| Nr 1 |
Parting tool; for slicing through
finished work in the lathe. |
| Nr 2 |
Roughing tool; for general cylindrical turning
and, when set at right angles to the lathe axis, for
facing. |
| Nr 3 |
The boring of cylinders would be performed with
this tool. |
| Nr 4 |
Right hand side cutting tool (i.e. produces a
right facing shoulder) for turning bar down and
finishing to a shoulder. |
| Nr 5 |
Left hand side cutting tool; will work close to
the chuck jaws for facing the end of bar. |
| Nr 6 |
Left hand side cutting tool for turning bar down
and finishing to a shoulder. |
|
£95.50
|
|
| RG50 |
7-12 HSS Werkzeugsatz
especially ground for Cowells. |
| Nr 7 |
Right hand straight shanked side
cutting tool. |
| Nr 8 |
Internal (nut) screwcutting tool. |
| Nr 9 |
Right hand side cutting tool; will work close to
the tailstock centre for facing the end of bar. |
| Nr 10 |
Boring tool; The cutting edge is ground square on
this tool for machining recesses within a bore. |
| Nr 11 |
External screwcutting tool. |
| Nr 12 |
Left hand straight shanked side cutting tool. |
|
£97.75
|
|
| RG51 |
Spaltsägenzubehör |
The attachment has a ground steel table
providing a flat smooth surface for the movement of the
work piece. The table is height adjustable so that the
depth of cut may be varied. The H.S.S. saw blade is driven
via a mandrel screwed to the lathe's nose spindle. A G13
adaptor is required when used on the 90CW lathe. The
attachment is supplied with a blade of the customers
choice, either.:-
63mm diameter x 0,40mm, 63mm diameter x 0,50mm
63mm diameter x 0,60mm, 63mm diameter x 0,80mm
The slitting saw will cut metals, plastic and woods and
ensure a straight square cut. |
£195.00
|
|
| RG52 |
Spaltsägenblätten |
Spaltsägenblätten 0,4mm, 0,5mm, 0,6mm und
0,8mm (je) |
£21.00
|
|
| RG53 |
Rollen-Feilauflage |
This Filing Rest, used in conjunction with
headstock spindle indexing, provides a means of generating
accurate parallel flats, squares, hexagons etc. One
example of its application is the ability to produce a
square drive on a clock winding spindle.
Principles of operation:-
The two flanged rollers of hardened steel are used to
guide a hand file across the work piece to produce a flat.
The depth of this flat is determined by the vertical
position of the rollers, and this, on the Cowells lathe,
is geared to the cross slide feedscrew. A drive block
which has a groove milled at an angle in one face, drives
the roller bracket up or down a pillar which is fixed by a
screw to the tapped hole in the saddle. The ratio provides
a change in the height of the rollers of 0.125mm for a one
division 0.025mm movement of the cross slide handwheel.
The roller flanges assist in controlling the length of the
flat. Mounted on the lathe's carriage the length of the
flat can be measured via the leadscrew handwheel. |
£195.75
|
|
| RG55 |
Vertikal-Frässchlitten |
The Vertical Milling Slide facilitates a wide
range of milling operations on the lathe. Of sturdy
construction the slide features a cast iron body with a
ground steel Tee slotted table. A full length adjustable
gib strip is fitted. Fine feed is provided through the
calibrated knurled knob graduated in 0.025mm increments.
The slide adds a vertical dimension to milling operations
on the lathe. The slide is secured to the lathe's
crosslide via its tee-bolts. |
£280.50
|
|
| RGB56 |
Winkelplatte |
Made of cast iron, slotted and machined
perfectly square on all faces |
£40.45
|
|
| RGB57 |
Maschinenschraubstock |
The vice body is of cast iron, machined to
close tolerances and has four fixing holes. The screw has a
hexagonal head to aid clamping. The steel jaw may be locked
into position via a cap head screw and square nut running in
its own channel in the vice body. Tee-nut fixings are
supplied. |
£92.40
|
|
| RG58 |
Kippbare Werkzeugauflage |
Of traditional design, the steel base clamps
to the lathe bed via a tee nut and locking lever. The
hardened steel toolrest may be turned through 360°
adjusted for height and locked into position. The toolrest
sub-assembly is hinged in order that it may be 'tipped
over' to allow closer inspection and further operations to
the workpiece. |
£222.00
|
|
| RGB61 |
Teilkopf
(inkl. eine Platte RGB62) |
The solid steel body of the dividing head is
ground on all faces and is drilled to accept studs up to 6mm
diameter. It is capable of being mounted on two of its
faces. The spindle has the same 14mm x 1mm thread as the
lathe chucks and is hollow with a no.0 Morse taper. The
spindle is driven by a 40:1 ratio worm and wheel; adjustable
to eliminate any backlash. A spindle clamp is also provided.
A steel raising block is also supplied should clearance for
the mounting of a 3 Jaw Chuck (RG9) on the Vertical Milling
Machine (B100) be required, for example. The unit is
supplied with fixing studs and the appropriate tee-nuts. |
£640.00
|
|
| RGB62 |
A - F Teilplatte |
These are of steel and are ground. Seven
plates are available (including a blank).
| Platte A - 15-21-37 |
| Platte B - 16-23-39 |
| Platte C - 17-27-41 |
| Platte D - 18-29-43 |
| Platte E - 19-31-47 |
| Platte F - 20-33-49 |
|
£55.00
(je)
|
|
| RGB63 |
Rohling-Teilplatte |
This may be machined by Cowells or the
customer to special requirements.
The above plates cover all numbers up to 40 and the
following up to 120:- 41, 42, 43, 44, 45, 46, 47, 48, 49,
50, 52, 54, 55, 56, 57, 58, 60, 62, 64, 65, 66, 68, 70, 72,
74, 75, 76, 78, 80, 82, 84, 85, 86, 88, 90, 92, 94, 95, 98,
100, 104, 105, 108, 110, 115, 116, and 120, and on to a
maximum of 392 divisions. |
£30.00
|
|
| RGB66 |
T-Muttern-Satz |
A set of six work securing Tee-nuts. Use them
for all tee slots, face plates etc |
£17.50
|
|
| RGB701 |
Backenfutter und Bohrfutter Dorne |
90CW 8mm shank to "OJ" (suits RGB14) |
£38.00
|
|
| RGB702 |
90CW 8mm shank to 3/8" x 24 tpi (suits RGB15) |
£33.00
|
|
| RGB703 |
90CW 8mm shank to M14 dia x 1mm pitch |
£55.00
|
|
| RG715 |
Messerdorne |
8mm dia Shank, 7,5mm dia head, M4 locking
thread |
£33.00
|
|
| RG716 |
8mm dia Shank, 7,5mm dia head, M6 locking
thread |
£33.00
|
|
| RGB723 |
Rohling-Dorne |
90CW 8mm shank to 20mm dia x 30mm length |
£26.00
|
|
| RG73 |
Sattelhebelvorschub |
An all steel assembly providing a rapid or
sensitive traverse to the lathe saddle. The lever feed is of
particular use to the clockmaker who may wish to quickly
mount a Tip over toolrest (RG58) for example; also for
commercial batch production. A clamp with locking lever is
fitted to the feed bar for positional adjustment. The saddle
may therefore, be used in any position along the lathe's
bed. Maximum stroke in any one position is 45mm (Not
recommended for use on 90ME lathe.) |
P.O.A.
|
|
| RG84 |
Knurling Tool |
The Knurling tool is supplied with a straight
form knurling wheel. Wheels are interchangeable. |
£49.00
|
|
| RG84A |
Knurling Wheels |
Chequered form knurling wheel for RG84 |
£33.00
|
|
| RG84B |
Straight form knurling wheel for RG84 |
£29.00
|
|
