| Zubehör für Cowells
Vertikal Fräsmaschine |
| RGB14 |
Bohrfutter |
Hoher Präzision 0 - 4mm Bohrfutter und Dorn |
£108.00
|
|
| RGB15 |
Bohrfutter |
0 - 6.3mm Bohrfutter und Dorn |
£61.50
|
|
| RGB16 |
Bohrfutter |
0 - 9.5mm Bohrfutter und Dorn |
£79.50
|
|
| B23 |
Englischer Spannzangensatz |
Imperial Collets for the (B100) Vertikal Fräsmaschine
are sized: 1/8", 3/16", 1/4", 3/8". |
£156.50
|
|
| B24 |
Metrischer Spannzangensatz |
Metric Collets for the (B100) Vertikal Fräsmaschine are sized:
3mm, 4mm, 5mm, 6mm, 7mm, 8mm, 9mm, l0mm. |
£310.00
|
| B25 |
Einzeine Spannzangen
|
Any imperial or metric size of Collet may be purchased. |
£41.00 (je)
|
| B26 |
Rohling-Spannzange |
A Blank Collet is available and can be bored and slit to a special
size requirement by the Vertikal Fräsmaschine owner or by Cowells,
(please contact us for details). |
£25.00
|
|
| RGB56 |
Winkelplatte |
The angle plate is of cast iron and is here depicted bolted to the lathe's
faceplate (RG28) thus ensuring that the surface about to be machined ("faced")
will be square to the surface mounted on the angle plate. |
£40.45
|
|
| RGB57 |
Maschinenschraubstock |
The vice body is of cast iron, machined to close tolerances and has four
fixing holes. The screw has a hexagonal head to aid clamping. The steel
jaw may be locked into position via a cap head screw and square nut running
in its own channel in the vice body. Tee-nut fixings are supplied. |
£92.40
|
|
| RGB61 |
Teilkopf
(inkl. eine Platte RGB62) |
The solid steel body of the dividing head is ground on all faces
and is drilled to accept studs up to 6mm diameter. It is capable of
being mounted on two of its faces. The spindle has the same 14mm x
1mm thread as the lathe chucks and is hollow with a nr. 0 Morse taper.
The spindle is driven by a 40:1 ratio worm and wheel; adjustable to
eliminate any backlash. A spindle clamp is also provided. A steel
raising block is also supplied should clearance for the mounting of
a 3 Jaw Chuck (RG9) on the Vertikal Fräsmaschine(B100) be required,
for example. The unit is supplied with fixing studs and the appropriate
tee-nuts. |
£549.00
|
|
| RGB62 |
A - F Teilplatte |
These are of steel and are ground. Seven plates are available (including
a blank).
| Platte A - 15-21-37 |
| Platte B - 16-23-39 |
| Platte C - 17-27-41 |
| Platte D - 18-29-43 |
| Platte E - 19-31-47 |
| Platte F - 20-33-49 |
|
£55.00
(je)
|
|
| RGB63 |
Rohling-Teilplatte |
This may be machined by Cowells or the customer to special requirements.
The above plates cover all numbers up to 40 and the following up to 120:-
41, 42, 43, 44, 45, 46, 47, 48, 49, 50, 52, 54, 55, 56, 57, 58, 60, 62,
64, 65, 66, 68, 70, 72, 74, 75, 76, 78, 80, 82, 84, 85, 86, 88, 90, 92,
94, 95, 98, 100, 104, 105, 108, 110, 115, 116, and 120, and on to a maximum
of 392 divisions. |
£30.00
|
|
| RGB66 |
T-Muttern-Satz |
A set of six work securing Tee-nuts. Use them for all tee slots, face
plates etc |
£17.50
|
|
| B67 |
Klemmsatz |
A set of tee-nuts, studs and clamps for securing work to the Vertikal
Fräsmaschine table. |
£70.00
|
|
| B68 |
15mm - 30mm Schlagmesser |
Bored to accept 3/16" dia. tooling. Two locking grub
screws are provided. |
£47.50
|
|
| B69 |
30mm - 60mm Schlagmesser |
The 30mm - 60mm flycutter is bored to accept 5/16" dia. tooling.
Two locking grub screws are provided. |
£57.00
|
|
| RGB70 |
Backenfutter und Bohrfutter Dorne |
Nr 6 - Vertikal Fräsmaschine/ suits (RGB14) 'OJ' |
£36.00
|
|
| Nr 7 - Vertikal Fräsmaschine/ 3/8 x 24/suits (RGB15) |
£29.00
|
| Nr 8 - Vertikal Fräsmaschine/14mm x 1,5mm |
£51.00
|
| RGB72 |
Rohling-Dorne (Nr. 4) |
V.F. 16,5mm dia x 40mm length |
£25.00
|
|
| BG74 |
Motor |
A 240/220 volt D.C. 125 watt output, continuously rated, 4000 r.p.m. motor.
May be used in conjunction with the BG74a (detailed below) |
P.O.A.
|
|
| BG74A |
Control Board |
An electric motor speed control board to be used with (BG74) D.C. Motor.
Supplied with a potentiometer and wiring diagram (AC input.) |
P.O.A.
|
|
| RGB82 |
Antriebsriemen |
V.F. Antriebsriemen f. (B100) Vertikal Fräsmaschine. |
P.O.A.
|
|
